Question

In: Other

Determine the force in members CD of the truss, and state if the member is in tension or compression.



image.png

Part A

Determine the force in members CD of the truss, and state if the member is in tension or compression. Take P = 1675 lb (Figure 1) 

Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalar for members in compression


Part B

 Determine the force in members HI of the truss, and state if the member is in tension or compression. Take P = 1675 lb 


Part C 

 Determine the force in members CJ of the truss, and state if the member is in tension or compression. Take P = 1675 lb. 

Solutions

Expert Solution

Please Thumb's Up,,,,////


Related Solutions

Determine the force developed in members FE, FC and BC of the truss and state if...
Determine the force developed in members FE, FC and BC of the truss and state if these members are in tension or compression. Given, Pin support at A and Roller support at D. Use Section Method.
Determine the force in each member of the truss supporting a floor deck
Determine the force in each member of the truss supporting a floor deck as shown in Fig. P4.28. The deck is simply supported on floor beams which, in turn, are connected to the joints of the truss. Thus, the uniformly distributed loading on the deck is transmitted by the floor beams as concentrated loads to the top joints of the truss.
The maximum allowable tensile force in the members of the truss is (Ft) max = 5 kN
Problem 6.26 The maximum allowable tensile force in the members of the truss is (Ft) max = 5 kN, and the maximum allowable compressive force is (Fc)max = 3.4 kN. (Figure 1) Part A Determine the maximum magnitude P of the two loads that can be applied to the truss. Express your answer to three significant figures and include the appropriate units.
The maximum allowable tensile force in the members of the truss is (Ft)max = 5.6 kN
Problem 6.24 The maximum allowable tensile force in the members of the truss is (Ft)max = 5.6 kN, and the maximum allowable compressive force is (Fe)max = 3 kN. Take d= 2 m (Figure 1) Part A Determine the maximum magnitude of load P that can be applied to the truss Express your answer to three significant figures and include the appropriate units. 
Zero force member in trusses are select one: a- in-needed members b- to prevent out of...
Zero force member in trusses are select one: a- in-needed members b- to prevent out of plane buckling c- to prevent in-plane buckling d- to prevent out of plane buckling and on-plane buckling e- used for architectural purposes
The purpose of this program is to identify the forces of each member of the truss below
 C++ Program Assignment The purpose of this program is to identify the forces of each member of the truss below (FAB, FAD, FBC, FBD, FBE, FCE, FDE) and to state whether they are in tension or compression. Use the example we worked in class to determine the reaction forces (Ax, Ay, and Cy) and complete the analysis by the Method of Joints. When you have finished the program, you will upload the .cpp file to D2L in the Assessment Dropbox folder...
Discuss the result of the design of fillet weld for a tie member of a truss...
Discuss the result of the design of fillet weld for a tie member of a truss consist of an angle section ISA 100 x 75 x 8 mm of Fe410 grade, is welded to an 8 mm gusset plate. Design a weld to transmit a load equal to the full strength of the member. Assume shop welding. If the gusset plates are connected by 2 angle section ISA 65 x 65 x 6 mm back to back to the same...
A pin-ended chord of a truss is treated as a member in a braced frame. Its...
A pin-ended chord of a truss is treated as a member in a braced frame. Its length is 12 ft. It must carry a tension dead load of 95 kips and live load of 180 kips along with a uniformly distributed transverse dead load of 1.2 kips/ft and live load of 2.3 kips/ft. Will a W8x67, A992 member be adequate if the transverse load is applied to put the bending about the strong axis? Determine by (a) LRFD and (b)...
Capillary number is proportional to { (viscous force) / (surface tension force) } and is used...
Capillary number is proportional to { (viscous force) / (surface tension force) } and is used in momentum transfer in general and atomization and 2-phase flow in beds of solids calculations in particular. It is equivalent to (We/Re). ___________ Which is the friction factor for ReD = 600 and e/D = 0.002 in pipe flow? ___________ What is the friction factor for ReD= 3 x 105 and D/e = 5000 in pipe flow?
Solve for the forces in truss members using the method of sections I just need an...
Solve for the forces in truss members using the method of sections I just need an example
ADVERTISEMENT
ADVERTISEMENT
ADVERTISEMENT