A uniform cylinder of radius 14 cm and mass 27 kg is mounted so as to...

A uniform cylinder of radius 14 cm and mass 27 kg is mounted so as to rotate freely about a horizontal axis that is parallel to and 9.3 cm from the central longitudinal axis of the cylinder. (a) What is the rotational inertia of the cylinder about the axis of rotation? (b) If the cylinder is released from rest with its central longitudinal axis at the same height as the axis about which the cylinder rotates, what is the angular speed of the cylinder as it passes through its lowest position?

Expert Solution

genius_generous answered 7 months ago

A uniform cylinder of radius 11 cm and mass 26 kg is mounted so as to...

A uniform cylinder of radius 11 cm and mass 26 kg is mounted so as to rotate freely about a horizontal axis that is parallel to and 8.6 cm from the central longitudinal axis of the cylinder. (a) What is the rotational inertia of the cylinder about the axis of rotation? (b) If the cylinder is released from rest with its central longitudinal axis at the same height as the axis about which the cylinder rotates, what is the angular...

A uniform cylinder of radius 11 cm and mass 24 kg is mounted so as to...

A uniform cylinder of radius 11 cm and mass 24 kg is mounted so as to rotate freely about a horizontal axis that is parallel to and 4.6 cm from the central longitudinal axis of the cylinder. (a) What is the rotational inertia of the cylinder about the axis of rotation? (b) If the cylinder is released from rest with its central longitudinal axis at the same height as the axis about which the cylinder rotates, what is the angular...

A uniform cylinder of radius R and mass M is mounted so as to rotate freely...

A uniform cylinder of radius R and mass M is mounted so as to rotate freely about a horizontal axis that is parallel to, and a distance h from the central longitudinal axis of the cylinder. (a) What is the rotational inertia of the cylinder about the axis of rotation? (b) If the cylinder is released from rest with its central longitudinal axis at the same height as the axis about which the cylinder rotates, what is the angular speed...

A grinding wheel is a uniform cylinder with a radius of 8.50 cm and a mass...

A grinding wheel is a uniform cylinder with a radius of 8.50 cm and a mass of 0.350 kg . A. Calculate its moment of inertia about its center. B. Calculate the applied torque needed to accelerate it from rest to 1950 rpm in 4.00 s if it is known to slow down from 1750 rpm to rest in 57.5 s .

A solid cylinder with a mass of 3 kg, a radius of 25 cm, and a...

A solid cylinder with a mass of 3 kg, a radius of 25 cm, and a length of 40 cm is rolling across a horizontal floor with a linear speed of 12 m/s. The cylinder then comes to a ramp, and, as it is rolling up this ramp without slipping, it is slowing down. When the cylinder finally comes to a stop and begins rolling back down the ramp, how high is it above the floor?

A uniform disk of mass 371 kg and radius 0.19 m is mounted on frictionless bearings...

A uniform disk of mass 371 kg and radius 0.19 m is mounted on frictionless bearings so it can rotate freely around a vertical axis through its center (see the following figure). A cord is wrapped around the rim of the disk and pulled with a force of 10 N. What is the angular velocity (in rad/s) at the instant the disk has completed four revolutions. The disk starts from rest. Group of answer choices 3.78 rad/s 3.87 rad/s 2.35...

A 4.50 kg solid cylinder with radius 10.0 cm is allowed to roll down a uniform...

A 4.50 kg solid cylinder with radius 10.0 cm is allowed to roll down a uniform slope that has been inclined at 22°. The cylinder is stationary at the top and the length of the incline is 5.50 meters. 1. What percentage of the total KE is rotational KE at the bottom of the ramp? 2. What is the angular acceleration of the cylinder as it rolls down the ramp? 3. Find the velocity of the cylinder at the bottom...

A disk of radius 14 cm and has a mass of 10 kg is attached to...

A disk of radius 14 cm and has a mass of 10 kg is attached to a hub which is a disk of mass 8 kg and radius 5cm. The disks are mounted on a frictionless axel that runs through the center. A rope passes over the hub and supports a 10 kg mass on one side and a 5 kg mass on the other. If the rope does not slip on the hub, a.) What is the tension in...

A solid, uniform cylinder with mass 8.25 kg and diameter 10.0 cm is spinning with angular...

A solid, uniform cylinder with mass 8.25 kg and diameter 10.0 cm is spinning with angular velocity 245 rpm on a thin, frictionless axle that passes along the cylinder axis. You design a simple friction-brake to stop the cylinder by pressing the brake against the outer rim with a normal force. The coefficient of kinetic friction between the brake and rim is 0.344.

A cylinder of mass 0.3 kg and radius 8 cm (and I = 1/2 mR2 )...

A cylinder of mass 0.3 kg and radius 8 cm (and I = 1/2 mR2 ) is placed at the top of a long, straight ramp of length 2 meters. The cylinder is released from rest and allowed to roll without slipping to the bottom. When it reaches the bottom, it is rotating at a rate of 6.5 rev/s. Answers included. Need the process. a) What is the linear speed at the bottom of the ramp? 3.3m/s b) What is...

Question