1. Describe the general characteristic of this pump series including pumpingmechanism type, housing material, bearing type, etc..

Give a scientific method or ways to determine, investigate, or analyze the characteristic and behaviour of electric-powered two and three wheelers in terms of the factors such as safety, travel time, accessibility, cost for a user. I need help for a research class on determining the characteristic and behaviour of people.

What is Freezing Range? Describe the significances of Freezing Range of a material in casting.

Air enters the diffuser of a ramjet engine at 22 kPa, 228 K and a velocity of 920 m/s, decelerating to a negligible velocity at the point at which heat is added. Using cold airstandard analysis with constant specific heats at 300K, determine the following if the exit pressure is 22 kPa and heat is added at 750 kJ per kg of air:
(a) The pressure at the diffuser exit, in kPa.

(b) The velocity at the nozzle exit, in m/s.

(c) If the fuel used requires a temperature of 900K to auto-ignite, is the craft moving fast enough to use this fuel? If not, what minimum speed must it be moving such that the air temperature after compression will ignite the fuel?

Five kg of oxygen (O​2​), initially at 430°C, fills a closed, rigid tank. Heat transfer from the oxygen occurs at the rate 425 W for 10 minutes. Assuming the ideal gas model with ​k
​ = 1.350 for the oxygen, determine its final temperature, in °C.

Can't seem to find the right equations to use for this one, so I'm getting pretty stumped. Any help would be greatly appreciated

In this exercise we will utilize the tables for superheated water vapor, (D-3). All graphs should be generated using plotting software, e.g. Excel, MatLab, etc. (If you use NIST, do NOT utilize the built-in plotting software to generate your graphs.) Plot the specific internal energy and the specific enthalpy Vs T(K) at 1 bar. (Use a reasonable number of available temperature values but include the maximum and minimum values.) The lower limit of the ordinate should be 2500kJ/kg and the lower limit of the abscissa should be 300K. Observe the nature of the relationships and based on these calculate the ratio of specific heats, gamma. Plot the compressibility factor as a function of temperature for 1 bar and 120 bar and comment on the significance of intermolecular forces. The compressibility factor of a gas is 0.94152 when the temperature, pressure and specific volume are -50 degree F, 30atm and 0.018317m^3/kg, respectively. Which gas is it?

(a) If you want to extrude a Y-shaped profile, what is the maximum allowable branch length you can obtain if you use a 4” billet? The Y-shaped profile has a design that contains three equal length of branches, 30° angle between the top two branches, and a wall thickness of 4 mm throughout.

(b) If the Y-shaped profile is extruded from “easy” aluminum alloys with an exiting speed of 60 m/min, how long does it take to finish one extrusion process using a 6 feet long billet? (Hint: Make assumptions on when extrusion starts and stops.)

Consider 6.9 kg of austenite containing 0.40 wt% C, cooled to below 727˚C (1341˚F).

(a) What is the proeutectoid phase?
(b) How many kilograms each of total ferrite and cementite form?
(c) How many kilograms each of pearlite and the proeutectoid phase form?

See Animated Figure 9.24

At the beginning of the compression process of an air standard Otto cycle, p1 = 1 bar, T1 = 300 K. The maximum temperature in the cycle is 2250 K and the compression ratio is 9.8. The engine has 4 cylinders and an engine displacement of Vd = 2.6 L. Determine per cylinder:

a) the volume at state 1. (IN LITERS) I have tried 2.8L 0.945 L and 0.789 L but i keep getting it wrong.

b) the air mass per cycle.

c) the heat addition per cycle, in kJ.

d) the heat rejection per cycle, in kJ.

e) the net work per cycle, in kJ.

f) the thermal efficiency.

g) the mean effective pressure, in bar.

h) Develop a full exergy accounting per cycle, in kJ. Let T0 = 300 K, p0 = 1 bar. i) Devise and evaluate the exergetic efficiency for the cycle.

A 4-cy wheel loader will be used to load trucks from a quarry stockpile of uniform aggregates (1" and over in size). The haul distance will be negligible. The aggregate has a loose unite weight of 2,750 lb/cy. Estimate the loader production in tons based on a 50 min-hour efficiency factor. Use a conservative cycle time and fill factor.

A string of length L = 1 is held fixed at both ends. The string is initially deformed into a shape given by u(x, t = 0) = sin^2(πx) and released. Assume a value of c2 = 1. Find the solution u(x, t) for the vibration of the string by separation of variables.

If the bond stiffness and bond length of the carbon to carbon bond are 90 N/M and 154 pm respectively estimate the youngs modulus of diamond. B) The structure of thermoplastics also contain many carbon to carbon bonds, but the elastic moduli of thermo =plastics are commmonly two orders of magnitude lower than that of diamond. Why?

Practice for Matlab. You can create own f(x).

a. Write code to find and plot a root using the modified secant method

b. Find the roots using the roots command - identify and plot root of interest

c. Use polyder and roots to find and plot the minimum value

d. use fminbnd to find and plot minimum value

Thank you!

The total cycle time of an automatied fiber placement (AFP) operation (sheet lamination), used to manufacture a section of the airplane fuselage, is 8 hours and 40 minutes. The setup time before the start of the operation is 10 minutes. After each layer is put down, an inspection stage is performed for 5 minutes. The AFP head requires cleaning cycle of 3 minutes every 7 layers.

a. If the part is made of 20 layers, what is the time required (in minutes) to lay down 1 layer?

b. What is the percentage of down time for this operation?

c. What is the total cycle time (in minutes) for making this part, if the lay down speed was doubled?